Formula D Pro/Am Round 5 preparations Part 1

So Round 5 will be our biggest event yet.  After not qualifying or placing in Round 2 from our transmission failure, we had to play catch up.  We have so far qualified mid range and finished 1st in the other rounds.  How we qualify and finish this round will determine the winner of the overall series.  We are currently 2nd in points standings.  However, if Tim (the current leader) qualifies higher and finishes slightly lower than us in Round 5 (say we get first and he wins second), he retains the overall points leader position, winning the series.  SO...game on.

We've been discussing a few things, and I won't disclose everything that's going on.  We have a "secret weapon" that we hope will give us the edge we need.  It's not something I'll disclose until the event, but it'll be pretty neat.

With our engine seeing compression as low as 112, we were averaging about 120.  Those are on the very low end of the spectrum, so we knew that it was getting weak.  The fear was that we would go out on the track, and the engine would just give up.  We definitely didn't want that to happen.  So the search began.  We ended up with CP Pistons and Eagle Rods, both of which received great reviews and had good prices.  Oil pump, water pump, and a few other goodies that came when we bought the engine will be swapped just in case.  We didn't want to get in a situation where either of these components failed during competition.  Although we had 10-15 minutes between runs to "fix" the car, we didn't want to be in that situation again.  Our manual boost controller was a great tool, but it still allowed for boost spikes.  So an EBC (electronic boost controller) is being installed for more control over the boost spectrum.

As of today, the motor is out.  Rods, Pistons, and the "secret weapon" have arrived.  ARP head bolts are on their way.  So to the machine shop the engine will go...

Overall, this will be a fun event, and we'll see what happens.  We are all on edge to see what will happen, and I'm sure our competitors who have read or seen our Facebook posts are all curious to see what we are doing.  Our little 350hp (estimated) SR20DET has done well keeping up with these 2JZ and other motor swapped cars with double our power.  We shall soon see who will be the victor in this year's battles.  It certainly has been an exciting one, and no matter the results, we plan on entering this series for the 2014 season as well.

Bryan Lin
CEO, The Motorsports Authority, Inc. | MSAStore.com | BCRacingDirect.com

Read More

Rewind...Power Cruise USA - Motorsports Ranch Houston: Drifting

What an eventful day.  After our travel woes, we finally made it to the event.  By the time we arrived, we were down a few cars.  Several had started to break misc parts and were no longer operational.

MSA Drift car getting prepped

Axle started the car and got on course.  It was interesting fitting the drifting between the "cruises" around the track and the short drag race events.  But it offered enough diversity to make it entertaining. The course was very large. Axle had enough areas to allow cool down periods for the car.

MSA Drift car testing out the track

We thoroughly enjoyed the track, but because of our tardiness, we were only able to make a few laps around the course during Day 1.


Day 2 proved to be more eventful. They shorten the track for the drift events to a more manageable area. Because of how the track was set up, it was difficult as a spectator to see the cars at all times and the shortened track was a huge improvement.

Being a "fun" track day event, Axle decided to see how far he could push the limits.  His goals were to see how much paint he could scrape off the corner of the car on the concrete dividers without damaging the car. He was successful. We ripped many of tires apart, including a time where he didn't notice the tire was gone and continued to drift the course.  One of the attempts was perfect. The car just barely kissed the wall.  However, the barrel on the other side of the turn was not so lucky. The impact smashed in the rear corner, sheared the retainer tabs, and popped off the rear fender flare. Shortly thereafter, a tire blew.  Despite what happened, it was an amazing watch for the spectators, and a much better setup for photos.

Overall, it was a good time. I will be posting our video of the event soon.

Bryan Lin
CEO, The Motorsports Authority, Inc. | MSAStore.com | BCRacingDirect.com


Notes from the driver...

Drifting at MSR Houston in the middle of summer is a huge treat and a bit of a nightmare at the same time. Road courses are a blast. Unlimited course design, unique corners, tighter limits... makes for some wild moments. On the flip side, road courses beat up a driver and car. Flying off track (you have to push to get better), rumble strips (I broke a wheel), and concrete walls... tire slaying heat, engine and fluids get too hot too fast. The organizers had us run the full course on day one, and it was very taxing. We had some fun, followed some friends around the track. Blasted the corners as best I could having "slept" in a well worn chevy passenger seat the night before. The next day however, was the real fun!

A good nights sleep did amazing things for my driving, and the course was shortened to a noodly shaped rectangle right in front of the stands. The first turn is identical to one in an iconic Japanese race track, theres a nice big slightly banked sweeper, and then a wall. I haven't had a comfortable opportunity to scrape a wall up until this point. The only wall you can scrape in Memphis is 100+ mph, and I love this car too much to try that mid season. Driving this smaller course in front of the crowd was great. It was a good opportunity to focus on a smaller set of corners, really get to push the limits. I got my wall scrape, but it wasn't enough, I had to try a couple more times and eventually knocked the bumper off. Tires were only lasting 4-5 laps at this point, I stayed on the gas all day!

 All in all it was a great time. One track I definitely want to go back to, just not too soon. Some local chinese topped the day off and we got back to the hotel for some shut eye. The return trip was uneventful. We kept the radiator full, and the throttle down. Enjoyed coming home after a good nights rest, we rarely leave an event in the daylight.

Axle

Read More